Line detection

The Hough transform{{Cite web|url=http://web.ipac.caltech.edu/staff/fmasci/home/astro_refs/HoughTrans_lines_09.pdf|title=Line Detection by Hough transformation}} can be used to detect lines and the output is a parametric description of the lines in an image, for example ρ = r cos(θ) + c sin(θ). If there is a line in a row and column based image space, it can be defined ρ, the distance from the origin to the line along a perpendicular to the line, and θ, the angle of the perpendicular projection from the origin to the line measured in degrees clockwise from the positive row axis. Therefore, a line in the image corresponds to a point in the Hough space.{{cite web|url=http://vision.stanford.edu/teaching/cs231a_autumn1112/lecture/lecture4_edges_lines_cs231a_marked.pdf |title=Finding lines: from detection to model fitting |first=Fei-Fei |last=Li |date=10 October 2011 |publisher=Stanford Vision Lab}} The Hough space for lines has therefore these two dimensions θ and ρ, and a line is represented by a single point corresponding to a unique set of these parameters. The Hough transform can then be implemented by choosing a set of values of ρ and θ to use. For each pixel ({{var|r}}, {{var|c}}) in the image, compute r cos(θ) + c sin(θ) for each values of θ, and place the result in the appropriate position in the (ρ, θ) array. At the end, the values of (ρ, θ) with the highest values in the array will correspond to strongest lines in the image

In a convolution-based technique, the line detector operator consists of a convolution masks tuned to detect the presence of lines of a particular width n and a θ orientation. Here are the four convolution masks to detect horizontal, vertical, oblique (+45 degrees), and oblique (−45 degrees) lines in an image.

a) Horizontal mask(R1)

(b) Vertical (R3)

(C) Oblique (+45 degrees)(R2)

(d) Oblique (−45 degrees)(R4)

In practice, masks are run over the image and the responses are combined given by the following equation:

R(x, y) = max(|R1 (x, y)|, |R2 (x, y)|, |R3 (x, y)|, |R4 (x, y)|)

If R(x, y) > T, then discontinuity

As can be seen below, if mask is overlay on the image (horizontal line), multiply the coincident values, and sum all these results, the output will be the (convolved image). For example, (−1)(0)+(−1)(0)+(−1)(0) + (2)(1) +(2)(1)+(2)(1) + (−1)(0)+(−1)(0)+(−1)(0) = 6 pixels on the second row, second column in the (convolved image) starting from the upper left corner of the horizontal lines. page 82

These masks above are tuned for light lines against a dark background, and would give a big negative response to dark lines against a light background.{{Cite web|url=https://homepages.inf.ed.ac.uk/rbf/HIPR2/linedet.htm|title=Line Detection|website=homepages.inf.ed.ac.uk|access-date=2018-04-23}}

The code was used to detect only the vertical lines in an image using Matlab and the result is below. The original image is the one on the top and the result is below it. As can be seen on the picture on the right, only the vertical lines were detected

File:Testbuilding.jpg

File:LineImage.png

clear all

clc

% this MATLAB program will only detect vertical lines in an image

building = imread('building.jpg'); % This will upload the image building

tol = 5; % define a tolerance in the angle to account for noise or edge

% that may look vertical but when the angle is computed

% it may not appear to be

[~, angle] = imgradient(building);

out = (angle >= 180 - tol | angle <= -180 + tol);

%this part will filter the line

out_filter = bwareaopen(out, 50);

figure, imshow(building), title('Original Image');

figure, imshow(out_filter), title('Detected Lines');

==See also==

• Digital image processing
• Canny edge detector
• Sobel operator

{{reflist}}

Category:Image processing

__FORCETOC__