Power Jets W.2

In 1940 the Air Ministry placed a contract with the Gloster Aircraft Company for prototypes of a new twin-engined jet fighter aircraft to the requirement of F.9/40, this aircraft became the Gloster Meteor. At the same time, Power Jets was authorised to design a new engine that was intended to power the same aircraft.Smith 1946, p. 87. The W.2 was built under contract by the Rover Car Company in the early 1940s. Relations between Power Jets and Rover were somewhat strained and development of the W.2 was very slow.

In late 1942, Rover agreed to exchange their jet engine factory at Barnoldswick, Lancashire for the Rolls-Royce Meteor tank engine factory in Nottingham, with no money changing hands. At the behest of the UK government, Rolls-Royce thereupon assumed control of the W.2 project, with Frank Whittle and his small team at Power Jets acting in an advisory capacity.Hooker 1984, Chapter 3. Together, they ironed out the problems with the W.2 and finally put the engine into mass production as the {{convert|1600|lbf|kN}} thrust Rolls-Royce Welland. These engines were installed in the Gloster Meteor F Mk1 and early F Mk3's and entered service in 1944.

After initial suggestions in 1939 by the Engine Department of the Royal Aircraft Establishment (RAE), the latter's Pyestock Section experimented with the technique of injecting fuel into the engine's exhaust nozzle, later known as reheat, and this technique was further refined after Power Jets and the personnel from Pyestock had been amalgamated. Reheat was later flight trialled in the W.2/700 engines in a Meteor I. The technique increased the Meteor's speed by 30-40 mph.{{Cite web| url=https://www.flightglobal.com/pdfarchive/view/1947/1947%20-%201359.html | title=Correspondence | access-date=16 April 2016 | archive-date=27 April 2016 | archive-url=https://web.archive.org/web/20160427182314/https://www.flightglobal.com/pdfarchive/view/1947/1947%20-%201359.html | url-status=dead}}

The Rover designations for engines produced at Barnoldswick were given a "B" prefix together with their own internal design number, e.g., "B.23". Later, after designs were transferred to Rolls-Royce (RR) an additional "R" was prefixed, changing the designation to "RB" to prevent possible confusion with US bomber designations, e.g., "RB.23". This "RB" designation system continues to be used within Rolls-Royce to this day.

File:Welland.JPG This design was later to become the Derwent]]

;W.2

:Design thrust of {{convert|1600|lbf|kN}} and a dry weight of approximately {{convert|850|lb}}. Early versions could not exceed 1,000lbf thrust without compressor surge and excessive exhaust gas temperature. Engines produced by Rover under subcontract to MAP. W.2 design quickly abandoned and replaced by W.2B after Whittle re-evaluated W.2 design and calculated exhaust gas velocity would approach Mach 1.

;W.2 Mark IV

:W.2 manufactured by British Thomson-Houston (BTH) but discovered to be sensitive to design assumptions, so changed in stages by Power Jets to bring in line with W.2B design. Wrecked by bursting of faulty new impeller forging on 10 October 1941 after completing "a useful amount of testing".{{Cite web| title=The early history of the Whittle jet propulsion gas turbine | url=http://www.imeche.org/docs/default-source/presidents-choice/jc12_1.pdf | archive-url=https://web.archive.org/web/20150924033909/http://www.imeche.org/docs/default-source/presidents-choice/jc12_1.pdf | archive-date=2015-09-24}}

;W.2Y

:Direct flow "straight-through" combustion chamber design, May 1940, not built.

;W.2B/Rover B.23

:Initial first two engines produced by Rover as the 'B.23' with one installed in E.28/39 W4046/G,{{Cite web| url=https://www.flightglobal.com/pdfarchive/view/1949/1949%20-%201793.html | title=Flight | access-date=16 April 2016 | archive-date=28 April 2016 | archive-url=https://web.archive.org/web/20160428000351/https://www.flightglobal.com/pdfarchive/view/1949/1949%20-%201793.html | url-status=dead}} other units built by BTH, and Power Jets.{{Cite web| url=https://www.flightglobal.com/pdfarchive/view/1946/1946%20-%200235.html | title="River Class" Evolution | access-date=16 April 2016 | archive-date=5 March 2016 | archive-url=https://web.archive.org/web/20160305070802/https://www.flightglobal.com/pdfarchive/view/1946/1946%20-%200235.html | url-status=dead}} Initially engines suffered failure of Rex 78 turbine blades, General Electric (GE) in the US sending Rover several improved sets of Hastelloy B blades in July 1942. Blade material later switched to Nimonic 80.{{Cite web| title=The historical evolution of turbomachinery | url=http://web.itu.edu.tr/aydere/history.pdf | archive-url=https://web.archive.org/web/20160512215221/http://web.itu.edu.tr/aydere/history.pdf | archive-date=2016-05-12}} Engine design later transferred to Rolls-Royce as prototype of the B.23 Welland, and also built in US as GE I-A.{{Cite web| url=https://www.flightglobal.com/pdfarchive/view/1945/1945%20-%202022.html | title=Early history of the whittle jet propulsion gas turbine | access-date=16 April 2016 | archive-date=27 April 2016 | archive-url=https://web.archive.org/web/20160427211716/https://www.flightglobal.com/pdfarchive/view/1945/1945%20-%202022.html | url-status=dead}} Re-designed 'B.23' combustion chambers for this engine designed by Joseph Lucas Ltd.{{Cite web| url=https://www.flightglobal.com/pdfarchive/view/1946/1946%20-%200024.html | title=Combustion Research | access-date=16 April 2016 | archive-date=28 April 2016 | archive-url=https://web.archive.org/web/20160428011110/https://www.flightglobal.com/pdfarchive/view/1946/1946%20-%200024.html | url-status=dead}}

;W.2B Mark II

:MAP-authorised Rover re-design using 10-vane diffuser designed by Rover/RR, and new turbine with fewer, broader blades. By Dec 1941 giving {{convert|1,510|lbf|kN}} without surging.{{Cite web| title=The historical evolution of turbomachinery | url=http://web.itu.edu.tr/aydere/history.pdf | archive-url=https://web.archive.org/web/20160512215221/http://web.itu.edu.tr/aydere/history.pdf | archive-date=2016-05-12}}

;W.2B/500 - Rover B.26

:W.2B with longer turbine blades and using diffuser of W.2B Mark II and new blower case and turbine design to give {{convert|1,850|lbf|kN}} at 16,750 rpm. First run in September 1942 attaining {{convert|1,755|lbf|kN}}. Sfc, 1.13 lb/(hr lbf) with jet pipe temperature of 606°C. Initially suffered from resonance at 14,000 rpm leading to impeller blade cracking. MAP-authorised re-design with straight-through combustion chambers by Adrian Lombard and John Herriot (the latter of the AID) at Rover as the B.26 with four test engines being built before design taken over by RR and after re-design for greater air flow becoming the B.37 Derwent.{{Cite web| url=https://www.flightglobal.com/pdfarchive/view/1946/1946%20-%200236.html | title="River Class" Evolution | access-date=16 April 2016 | archive-date=3 July 2017 | archive-url=https://web.archive.org/web/20170703162857/https://www.flightglobal.com/pdfarchive/view/1946/1946%20-%200236.html | url-status=dead}} 'B.26' combustion chambers designed by Joseph Lucas Ltd.

;W.2/700

:New 'Type 16' compressor diffuser, new compressor casing, plus improved compressor rotor sent over from GE,"World Encyclopedia of Aero Engines - 5th edition" by Bill Gunston, Sutton Publishing, 2006, p.160 all combined to produce 80% compressor efficiency, Nimonic 80 turbine blades, and a static thrust of {{convert|2,000|lbf|kN}} at 16,700 rpm. By 1944 producing {{convert|2,485|lbf|kN}} at a pressure ratio of 4:1{{Cite web| title=The historical evolution of turbomachinery | url=http://web.itu.edu.tr/aydere/history.pdf | archive-url=https://web.archive.org/web/20160512215221/http://web.itu.edu.tr/aydere/history.pdf | archive-date=2016-05-12}} with airflow of 47.15 lb/s from same size engine as W.1.{{Cite web| url=https://www.flightglobal.com/pdfarchive/view/1947/1947%20-%201359.html | title=Correspondence | access-date=16 April 2016 | archive-date=27 April 2016 | archive-url=https://web.archive.org/web/20160427182314/https://www.flightglobal.com/pdfarchive/view/1947/1947%20-%201359.html | url-status=dead}} Sfc, 1.05 lb/(hr lbf) with jet pipe temperature of 647°C. Flight-tested reheat in Meteor I EE215/G increasing top speed from 420 mph to 460 mph.{{Cite web| url=https://www.flightglobal.com/pdfarchive/view/1955/1955%20-%200729.html | title=Under the heading "Altitude Restrictions" an entry on the Limitations Sheet read | access-date=19 April 2016 | archive-date=7 May 2016 | archive-url=https://web.archive.org/web/20160507033057/https://www.flightglobal.com/pdfarchive/view/1955/1955%20-%200729.html | url-status=dead}} Flight-tested to 505 mph at 30,000 feet in E.28/39 W4046/G.{{Cite web| url=https://www.flightglobal.com/pdfarchive/view/1951/1951%20-%200884.html | title=Britain's Turbine Aircraft\ | access-date=25 April 2016 | archive-date=13 May 2016 | archive-url=https://web.archive.org/web/20160513204106/https://www.flightglobal.com/pdfarchive/view/1951/1951%20-%200884.html | url-status=dead}} Also ground-tested with aft ducted fan."World Encyclopedia of Aero Engines - 5th edition" by Bill Gunston, Sutton Publishing, 2006, p.160

;W.2/800

:W.2/700 with longer turbine blades for greater thrust. Suffered from turbine blade failure.

;W.2/850

:A developed version of greater thrust of {{convert|2,485|lbf|kN}} at 16,500 rpm and a higher dry weight of {{convert|950|lb}}.

;Rolls-Royce B.23 Welland

:Mass produced version of the W.2B/Rover B.23 for Meteor I. Developed {{convert|1,600|lbf|kN}} static thrust. Sfc, 1.12 lb/(hr lbf). 100 produced. Uprated to {{convert|1,700|lbf|kN}} thrust with nozzle inserts for chasing V-1's. Type-tested to 500 hours, into service for Meteor I at 150 hours time between overhaul (TBO)."World Encyclopedia of Aero Engines - 5th edition" by Bill Gunston, Sutton Publishing, 2006, p.192

;Rolls-Royce B.37 Derwent I

:Combined design based on W.2B/500 and Rover B.26 for Meteor III. Straight-through development of the 'trombone' style W.2 configuration, using already tooled-up compressor casing for Welland, new RR diffuser, and with compressor and turbine air and gas flow increased by 25% to give {{convert|2,000|lbf|kN}} static thrust. First tested July 1943. Type-tested to 500 hours, into service for Meteor III at 150 hours TBO.

The following aircraft were used for test purposes only:

• Gloster E.28/39
• F.9/40
• Vickers Wellington

The W.2B/700 was to be used in the Miles M.52 supersonic research aircraft. In order to achieve the thrust required for supersonic flight, a version of the engine was developed using a turbine-driven "augmenter" ducted fan (an early form of turbofan). The NO.4 augmenter was mounted behind the engine, drawing fresh air through ducts surrounding the engine. Power was boosted even further by supplying the air to the world's first "reheat jetpipe" or afterburner which was actually a very early athodyd or ramjet. The hope was that this combination of the W.2/700, turbofan augmenter and re-heat/ramjet would produce the required power for the proposed 1,000 mph aircraft.Eric Brown 2012, The Miles M.52: Gateway to Supersonic Flight

• A preserved W.2/700 is on public display at the Farnborough Air Sciences Trust.
• Another W.2/700 is part of the aero engine collection at Royal Air Force Museum Cosford.
• A W.2/700 is on display at Cranfield University. Awarded Engineering Heritage Award no.102.
• A sectioned W.2/700 at Lutterworth Museum
• W.2/500 at RAF museum London
• A Rover W.2B/26 is on display at the Midland Air Museum.

{{jetspecs

|

|ref=Jane'sJane's 1989, p. 266.

|type=Centrifugal flow turbojet

|length=

|diameter=

|weight=950 lb (431 kg)

|compressor=Single-stage double-sided centrifugal flow

|combustion= 10 reverse-flow

|turbine=Single stage axial flow

|fueltype=Kerosene

|oilsystem=

|power=

|thrust=2,485 lbf (1,127 kgf) at 16,500 rpm

|compression=4:1

|aircon=47 lb/s (21 kg/s)

|turbinetemp=

|fuelcon=2,610 lb/hr (1,185 kg/hr)

|specfuelcon=

|power/weight=

|thrust/weight=2.6

}}

{{Aircontent

|related=

• Power Jets W.1
• General Electric I-A
• Rolls-Royce Welland

|similar engines=

|lists=

• List of aircraft engines

|see also=

}}

{{Reflist}}

{{refbegin}}

• Gunston, Bill. World Encyclopedia of Aero Engines. Cambridge, England. Patrick Stephens Limited, 1989. {{ISBN|1-85260-163-9}}
• Jane's Fighting Aircraft of World War II. London. Studio Editions Ltd, 1998. {{ISBN|0-517-67964-7}}
• Smith, Geoffrey G.Gas Turbines and Jet Propulsion for Aircraft, London S.E.1, Flight Publishing Co.Ltd., 1946.
• {{cite book|last=Kay|first=Anthony L.|title=Turbojet History and Development 1930-1960 |publisher=The Crowood Press|location=Ramsbury|date=2007|edition=1st|volume=1|isbn=978-1-86126-912-6}}
• Hooker, Sir Stanley. "Not much of an Engineer". Airlife, England, 1984. {{ISBN|0 906393 35 3}}

{{refend}}

{{commons category}}

• [http://www.flightglobal.com/pdfarchive/view/1945/1945%20-%202022.html Flight, October 1945 - Sectional diagram of the W.2B]
• [http://www.flightglobal.com/pdfarchive/view/1962/1962%20-%200757.html A photograph in a 1962 issue of Flight of the Wellington W5389/G with W.2B installed]

{{Power Jets aeroengines}}

Category:1940s turbojet engines

Category:Centrifugal-flow turbojet engines

W.2