Sido S.1
| {{Infobox aircraft begin
| name=Sido 1 | image=Sido S-1 1.jpg | caption= }}{{Infobox aircraft type | type=Trainer aircraft | national origin=Poland | manufacturer= | designer=Józef Sido | first flight=late July 1930 | introduced= | retired= | status= | primary user= | more users= | produced= | number built=6 | program cost= | unit cost= | developed from= | variants with their own articles= }} |
The Sido S.1 was a Polish two seat, parasol wing trainer aircraft, first flown in 1930.
Design and development
In the late 1920s the LOPP issued a requirement for a low cost, {{convert|80|hp|kW|abbr=on|order=flip}} club trainer. In 1929 the Sido S.1 was designed in response by the amateur Józef Sido, who was a student at the Mining Academy in Kraków. Positive reactions from both LOPP and the Kraków Academic Aeroclub led to the parallel construction of three airframes in the workshops of the local Air Regiment, differing primarily in their engines. The first, powered by a {{convert|85|hp|kW|abbr=on|order=flip}} Cirrus III inline, flew for the first time on ether 21 or 28 July 1930. The second airframe flew in September 1930, initially known as the S.2 and fitted with a {{convert|80|hp|kW|abbr=on|order=flip}} Avia W.Z.7, a Polish seven cylinder radial engine. The third, initially known as the S.3, had the Cirrus engine but had modified the wing bracing struts and undercarriage. In the late summer of 1931 the two later aircraft were modified to the standards and engine of the S.1 and were referred to by that designation.
The wooden parasol wing of the Sido S.1 was built in two parts. Each had two spars, plywood skinned leading edges and was fabric covered. In plan the wing was straight tapered and its section varied outboard from S.T.Ae 74 to Göttingen Gö 398. Each halfwing was joined to the lower fuselage longerons with V-struts to the spars and the centre section, formed from the fuel tank, was held well above the fuselage on steel tube struts to the upper fuselage.
Its flat-sided fuselage was built around a steel tube structure and fabric covered apart from plywood decking. There were two open, tandem cockpits equipped with dual control. The upward field of view from the rear cockpit was improved with a wide, rounded, trailing edge cut-out and access to the front cockpit with a starboard-side door. The S.1 had a triangular fin and a large rudder with a leading edge that extended the straight edge of the fin but with a full, rounded trailing edge down to the keel. The tailplane was mounted on top of the fuselage, strut braced from below, and the elevators had a cut-out for rudder movement.
The S.1 had conventional, fixed landing gear. Each maninwheel was on a half-axle hinged from the lower fuselage longeron, as was the radius arm. The landing leg, which incorporated a compressed rubber shock absorber, was hinged from the upper longeron.
Operational history
The Polish military aviation authorities considered the S.1 alongside the PZL.5 and the M.N.5 for their trainer requirements. Despite its good performance, the lack of an established manufacturing facility for this amateur design prevented its military adoption. There was more enthusiasm from the civilian aeroclubs and a series of five airframes, designated S.1bis Z, powered by the Avia engine in a Townend ring cowling and fitted with streamlined wing struts, was begun in the newly established Central Aeroclubs' Workshops (C.W.A.). C.W.A went bankrupt after producing only three, the last of which had a {{convert|80|hp|kW|abbr=on|order=flip}} Siemens-Halske Sh 11 radial.
The S.1s was a frequent competitor in Polish meetings, including the National Lightplane Contests and many local and regional meetings and rallies through the early 1930s, though without major successes. It also served as a reliable and forgiving club trainer, the small production numbers reflecting the failure to find an established constructor for the aircraft rather than its qualities. One remained in use until 1939 and may have been evacuated to Romania.
Variants
;S.1: First prototype, Cirrus engine.
;S.2: Second prototype, Avia engine. Later re-engined with Cirrus and re-designate S.1.
;S.3: Third prototype, Cirrus engine. Later re-designated S.1.
;S.1 bis Z: Three built, the first two with Avia engines and the last with a Siemens.
Specifications (S.1)
{{Aircraft specs
|prime units?=met
|genhide=
|crew=Two
|capacity=
|length m=7.8
|length note=
|span m=11.4
|span note=
|height m=2.5
|height ft=
|height in=
|height note=
|wing area sqm=17
|wing area note=
|aspect ratio=
|airfoil=
|empty weight kg=456
|empty weight note=
|gross weight kg=700
|gross weight lb=
|gross weight note=
|max takeoff weight kg=
|max takeoff weight lb=
|max takeoff weight note=
|fuel capacity=
|more general=
|eng1 number=1
|eng1 name=Cirrus III
|eng1 type=air-cooled 4-cylinder inline
|eng1 hp=85
|eng1 note=
|power original=
|prop blade number=
|prop name=
|prop dia m=
|prop dia ft=
|prop dia in=
|prop dia note=
|perfhide=
|max speed kmh=170
|max speed note=at sea level
|cruise speed kmh=140
|cruise speed note=
|stall speed kmh=
|stall speed mph=
|stall speed kts=
|stall speed note=
|never exceed speed kmh=
|never exceed speed mph=
|never exceed speed kts=
|never exceed speed note=
|range km=700
|range note=
|endurance=
|ceiling m=4500
|ceiling note=
|g limits=
|roll rate=
|glide ratio=
|climb rate ms=
|climb rate ftmin=
|climb rate note=
|time to altitude=6 min to {{convert|1000|m|ft|abbr=on}}
|sink rate ms=
|sink rate ftmin=
|sink rate note=
|lift to drag=
|wing loading kg/m2=
|wing loading lb/sqft=
|wing loading note=
|fuel consumption kg/km=
|fuel consumption lb/mi=
|power/mass=
|thrust/weight=
|more performance=
- 'Take-off run: {{convert|90|m|ft|abbr=on}}
- Landing speed: {{convert|60|km/h|mph|abbr=on}}
}}