USCGC Point Orient

Point Orient was built to accommodate an 8-man crew.Scheina, p 71 She was powered by two {{convert|600|hp|0|abbr=on}} VT600 Cummins diesel main drive engines and had two five-bladed {{convert|42|inch|m|abbr=on}} propellers. The main drive engines were later replaced by {{convert|800|hp|0|abbr=on}} VT800 Cummins engines. Water tank capacity was {{convert|1550|gal|liters|}} and fuel tank capacity was {{convert|1840|gal|liters|}} at 95% full.Scheina, p 71 Engine exhaust was ported through the transom rather than through a conventional stack and this permitted a 360 degree view from the bridge; a feature that was very useful in search and rescue work as well as a combat environment.Scotti, p 165

The design specifications for Point Orient included a steel hull for durability and an aluminum superstructure and longitudinally framed construction was used to save weight. Ease of operation with a small crew size was possible because of the non-manned main drive engine spaces. Controls and alarms located on the bridge allowed one man operation of the cutter thus eliminating a live engineer watch in the engine room.Scotti, p 165 Because of design, four men could operate the cutter; however, the need for resting watchstanders brought the crew size to eight men for normal domestic service.Scotti, p 165 The screws were designed for ease of replacement and could be changed without removing the cutter from the water. A clutch-in idle speed of three knots helped to conserve fuel on lengthy patrols and an eighteen knot maximum speed could get the cutter on scene quickly.Scotti, p 166 Air-conditioned interior spaces were a part of the original design for the Point class cutter. Interior access to the deckhouse was through a watertight door on the starboard side aft of the deckhouse. The deckhouse contained the cabin for the officer-in-charge and the executive petty officer.Scotti, p 166 The deckhouse also included a small arms locker, scuttlebutt, a small desk and head. Access to the lower deck and engine room was down a ladder. At the bottom of the ladder was the galley, mess and recreation deck. A watertight door at the front of the mess bulkhead led to the main crew quarters which was ten feet long and included six bunks that could be stowed, three bunks on each side. Forward of the bunks was the crew's head complete with a compact sink, shower and commode.Scotti, p 166 Accommodations for a 13-man crew were installed for Vietnam service.Scheina, p 72Scotti, p 10Scotti, p 219

After delivery in 1961, Point Orient was assigned a homeport of Fort Pierce, Florida, where she served as a law enforcement and search and rescue patrol boat. On 15 January 1965, she towed the disabled MV Sally {{convert|120|mi|km}} southeast of Corpus Christi, Texas, to safety.

At the request of the United States Navy, in April 1965, she was alerted for service in South Vietnam and assigned to Coast Guard Squadron One in support of Operation Market Time along with 16 other Point class cutters.Larzelere, p 13Cutler, p 84 While the crew completed overseas training and weapons qualifications at Coast Guard Island and Camp Parks, California, Point Orient was loaded onto a merchant ship, and transported to Subic Bay, Philippines in May 1965 where she was refitted for combat service. Shipyard modifications included installation of new single-sideband radio equipment, additional floodlights, small arms lockers, additional sound-powered phone circuits, and the addition of four M2 machine guns. The original bow-mounted machine gun was replaced with a combination over-under .50 caliber machine gun/81mm trigger-fired mortar that had been developed by the Coast Guard for service in Vietnam.Larzelere, p 21Cutler, p 82

For service in Vietnam, two officers were added to the crew complement to add seniority to the crew in the mission of interdicting vessels at sea.Larzelere, p 15

Point Orient was assigned to Division 12 of Squadron One to be based at Da Nang, along with {{USCGC|Point Arden|WPB-82309|6}}, {{USCGC|Point Caution|WPB-82301|6}}, {{USCGC|Point Dume|WPB-82325|6}}, {{USCGC|Point Ellis|WPB-82330|6}}, {{USCGC|Point Gammon|WPB-82328|6}} and {{USCGC|Point Welcome|WPB-82329|6}}. After sea trials, the Division left Subic Bay for Da Nang on 16 July 1965 in the company of {{USS|Snohomish County|LST-1125|6}}, their temporary support ship. After almost two weeks at sea, they arrived at their new duty station on 20 July and began patrolling the coastal waters near Da Nang.Larzelere, p 22 Duty consisted of boarding Vietnamese junks to search for contraband weapons and ammunition and check the identification papers of persons on board. Permanent engineering and logistic support of Division 12 was provided by a U.S. Navy non-self-propelled floating workshop, YR-71. Point Orient became the first Coast Guard unit in Vietnam to engage the enemy on 24 July 1965 after being fired on from the shore by machine guns and mortars while attempting to board a junk. She returned fire but the results were unknown.Larzelere, p 31 During this time, the WPB's were directed to paint the hulls and superstructures formula 20 deck gray to cover the stateside white paint. This increased the effectiveness of night patrols.Larzelere p 54Cutler, p 85

On 22 March 1969, Chief Engineman Morris S. Beeson, Engineering Officer of the Point Orient crew was killed in action while the cutter's small boat was attempting to interdict three sampans entering a restricted zone in Quảng Trị Province.Scotti, p 163[http://www.vvmf.org/thewall/Wall_Id_No=3257 Vietnam Veterans Memorial Virtual Wall – Beeson] Beeson was one of seven Coast Guardsmen killed in action during the Vietnam War.

On 14 July 1970, Point Orient was given to the Republic of Vietnam Navy and recommissioned as RVNS Nguyễn Kim Hưng (HQ-722).Scotti, p 211

;Notes

{{reflist|2}}

;Bibliography

• {{cite book|last=Cutler|first=Thomas J.|author-link=Thomas J. Cutler|title=Brown Water, Black Berets: Coastal and Riverine Warfare in Vietnam|year=2000|publisher=Naval Institute Press, Annapolis|isbn=978-1-55750-196-7}}
• {{cite book|last=Larzelere|first=Alex|year=1997|title=The Coast Guard at War, Vietnam, 1965–1975|publisher=Naval Institute Press, Annapolis|isbn=978-1-55750-529-3}}
• {{cite book|last=Scheina|first=Robert L.|year=1990|title=U.S. Coast Guard Cutters & Craft, 1946–1990|publisher=Naval Institute Press, Annapolis|isbn=978-0-87021-719-7}}
• {{cite book|last=Scotti|first=Paul C.|year=2000|title=Coast Guard Action in Vietnam: Stories of Those Who Served|publisher=Hellgate Press, Central Point, OR|isbn=978-1-55571-528-1}}
• {{cite web|last=Wells II|first=William R.|title=The United States Coast Guard's Piggyback 81mm Mortar/.50 cal. machine gun|publisher=Vietnam Magazine|date=August 1997|url=http://www.pcf45.com/misfire/81-50.html|access-date=8 October 2010}}

• [http://www.uscg.mil/history/webcutters/Point_Class_WPB_Index.asp "Point" Class 82-foot WPBs] Coast Guard Historian's website

{{Point class cutter}}

{{Use dmy dates|date=August 2019}}

{{DEFAULTSORT:Point Orient}}

Orient

Category:1961 ships

Category:Vietnam War patrol vessels of the United States

Category:United States Coast Guard ships transferred to the Republic of Vietnam Navy

Category:Ships built by the United States Coast Guard Yard