USCGC Point Partridge

Point Partridge was built to accommodate an 8-man crew.Scheina, p 71 She was powered by two {{convert|600|hp|0|abbr=on}} VT600 Cummins diesel main drive engines and had two five-bladed {{convert|42|inch|m|abbr=on}} propellers. The main drive engines were later replaced by {{convert|800|hp|0|abbr=on}} VT800 Cummins engines. Water tank capacity was {{convert|1550|gal|liters|}} and fuel tank capacity was {{convert|1840|gal|liters|}} at 95% full.Scheina, p 71 Engine exhaust was ported through the transom rather than through a conventional stack and this permitted a 360-degree view from the bridge; a feature that was very useful in search and rescue work as well as a combat environment.Scotti, p 165

The design specifications for Point Partridge included a steel hull for durability and an aluminum superstructure and longitudinally framed construction was used to save weight. Ease of operation with a small crew size was possible because of the non-manned main drive engine spaces. Controls and alarms located on the bridge allowed one man operation of the cutter thus eliminating a live engineer watch in the engine room.Scotti, p 165 Because of design, four men could operate the cutter; however, the need for resting watchstanders brought the crew size to eight men for normal domestic service.Scotti, p 165 The screws were designed for ease of replacement and could be changed without removing the cutter from the water. A clutch-in idle speed of three knots helped to conserve fuel on lengthy patrols and an eighteen knot maximum speed could get the cutter on scene quickly.Scotti, p 166 Air-conditioned interior spaces were a part of the original design for the Point class cutter. Interior access to the deckhouse was through a watertight door on the starboard side aft of the deckhouse. The deckhouse contained the cabin for the officer-in-charge and the executive petty officer.Scotti, p 166 The deckhouse also included a small arms locker, scuttlebutt, a small desk and head. Access to the lower deck and engine room was down a ladder. At the bottom of the ladder was the galley, mess and recreation deck. A watertight door at the front of the mess bulkhead led to the main crew quarters which was ten feet long and included six bunks that could be stowed, three bunks on each side. Forward of the bunks was the crew's head complete with a compact sink, shower and commode.Scotti, p 166 Accommodations for a 13-man crew were installed for Vietnam service.Scheina, p 72Scotti, p 10Scotti, p 219

After delivery in 1960, Point Partridge was assigned a homeport of Jonesport, Maine, where she served as a law enforcement and search and rescue patrol boat.

At the request of the United States Navy, in October 1965, she was alerted for service in South Vietnam and assigned to Coast Guard Squadron One in support of Operation Market Time along with 8 other Point class cutters.Larzelere, p 72Cutler, p 84 While the crew completed overseas training and weapons qualifications at Coast Guard Island and Camp Parks, California, Point Partridge was loaded onto a merchant ship, and transported to Subic Bay, Philippines arriving in January 1966 where she was refitted for combat service. Shipyard modifications included installation of new single-sideband radio equipment, additional floodlights, small arms lockers, bunks, additional sound-powered phone circuits, and the addition of 4 M2 machine guns. The original Oerlikon 20 mm cannon was replaced with a combination over-under .50 caliber machine gun/81mm trigger-fired mortar that had been developed by the Coast Guard for service in Vietnam.Larzelere, p 21Cutler, p 82 For service in Vietnam, two officers were added to the crew complement to add seniority to the crew in the mission of interdicting vessels at sea.Larzelere, p 15

Point Partridge was assigned to Division 13 of Squadron One to be based at Cat Lo Naval Base near Vung Tau, along with {{USCGC|Point Cypress|WPB-82326|6}}, {{USCGC|Point Grace|WPB-82323|6}}, {{USCGC|Point Hudson|WPB-82322|6}}, {{USCGC|Point Jefferson|WPB-82306|6}}, {{USCGC|Point Kennedy|WPB-82320|6}}, {{USCGC|Point League|WPB-82304|6}}, {{USCGC|Point Slocum|WPB-82313|6}} and {{USCGC|Point White|WPB-82308|6}}. After sea trials, the Division left Subic Bay for Cat Lo on 19 February 1966 in the company of {{USS|Forster|DER-334|6}}, their temporary support ship. They arrived at their new duty station on 23 February and began patrolling the coastal waters near the Rung Sat Special Zone.Kelley, p 5-450Larzelere, p 80 Duty consisted of boarding Vietnamese junks to search for contraband weapons and ammunition and check the identification papers of persons on board.

In February 1966 Operation Jackstay was conceived. The operation was a plan to deny food and water to the Viet Cong (VC) hidden in the Rung Sat Special Zone by cutting off resupply junks that had to cross the Soài Rạp River.Scotti, p 179 The interdiction efforts depended on using boats that were heavily armed, highly maneuverable and had a shallow draft; all characteristics of the Point Class cutter.Larzelere, p 80 Some of the Squadron One cutters were assigned in March 1966 to the operation and began 24-hour patrols on 10 March. The operation ended on 6 April; however, Point Partridge remained on the river patrol and had several contacts with VC supply junks during April and May 1966.Larzelere, p 83 From 1 to 6 May she was involved every night with enemy junks or attacks from the shoreline.Larzelere, p 83 During the rest of the month she managed to capture two junks; one loaded with weapons and the other containing {{convert|3500|lb|kg}} of rice.Scotti, p 170Tulich, p 6

In early 1970, Point Partridge and Point Jefferson acting as a team made over 300 boardings. Civic action programs conducted during the boardings by the two Squadron One cutters included handing out 3000 bars of soap as well as food items. Twelve Vietnamese were given medical treatment.Tulich, p 8

As a part of the Vietnamization program Republic of Vietnam Navy (RVNN) crewmen were assigned to the cutter for training purposes beginning in February 1969. After the crew of Point Partridge trained an RVNN replacement crew, she was turned over to the RVNN and recommissioned as RVNS Bùi Viết Thành (HQ-715), 27 March 1970.

;Notes

{{reflist}}

;Bibliography

• {{cite book|last=Cutler|first=Thomas J.|author-link=Thomas J. Cutler|year=2000|title=Brown Water, Black Berets: Coastal and Riverine Warfare in Vietnam|publisher=Naval Institute Press, Annapolis|isbn=978-1-55750-196-7}}
• {{cite book|last=Kelley|first=Michael P.|year=2002|title=Where We Were in Vietnam|publisher=Hellgate Press, Central Point, OR|isbn=978-1-55571-625-7}}
• {{cite book|last=Larzelere|first=Alex|year=1997|title=The Coast Guard at War, Vietnam, 1965-1975|publisher=Naval Institute Press, Annapolis|isbn=978-1-55750-529-3}}
• {{cite book|last=Scheina|first=Robert L.|year=1990|title=U.S. Coast Guard Cutters & Craft, 1946-1990|publisher=Naval Institute Press, Annapolis|isbn=978-0-87021-719-7}}
• {{cite book|last=Scotti|first=Paul C.|year=2000|title=Coast Guard Action in Vietnam: Stories of Those Who Served|publisher=Hellgate Press, Central Point, OR|isbn=978-1-55571-528-1}}
• {{cite web|last=Wells II|first=William R.|title=The United States Coast Guard's Piggyback 81mm Mortar/.50 cal. machine gun|publisher=Vietnam Magazine|date=August 1997|url=http://www.pcf45.com/misfire/81-50.html|access-date=8 October 2010}}
• {{cite web|last=Tulich|first=Eugene N.|title=The United States Coast Guard in South East Asia During the Vietnam Conflict|publisher=U.S. Coast Guard History Office|year=1975|url=http://www.uscg.mil/history/articles/h_tulichvietnam.asp|access-date=16 March 2011}}

• [http://www.uscg.mil/history/webcutters/Point_Class_WPB_Index.asp "Point" Class 82-foot WPBs] Coast Guard Historian's website

{{Point class cutter}}

{{DEFAULTSORT:Point Partridge}}

Partridge

Category:1960 ships

Category:Vietnam War patrol vessels of the United States

Category:United States Coast Guard ships transferred to the Republic of Vietnam Navy

Category:Ships built by the United States Coast Guard Yard