core rope memory

Similar to magnetic-core memory, magnetic rings (or cores) are used to determine the data of the software. Unlike magnetic-core memory, the cores themselves are not used to store the data; the way a core is wired controls whether that core represents a '0' or a '1'.

There are three main types of functions a wire can have in core rope memory:

• Set/reset: These are used to change all of the cores from one polarity to another.
• Sense: A sense wire can detect a change in a core's polarity. It can pass through a core to indicate one bit state (typically '1') or bypass it to represent the other (typically '0').
• Inhibit: Inhibit wires are used effectively to address which core to select.

To read from core rope memory, the set/reset wire is given a strong current to change the polarity of the cores. This induces a small voltage on the sense wires passing through them, which can then be used to interpret binary data. The inhibit wires pass a current in the opposite direction of the set/reset wire for all cores but the desired one, acting like a memory addressing system. This prevents the sense wires from detecting polarity changes from the other magnetic cores.

The sense wires are used to encode the data by either going through a core or bypassing it. By using many sense wires, multiple bits of data can be stored for each core. In the case of the Apollo Guidance Computer, each core had 192 sense wires passing through it, which could store 12 16-bit words per core.{{Cite web |title=Software woven into wire: Core rope and the Apollo Guidance Computer |url=http://www.righto.com/2019/07/software-woven-into-wire-core-rope-and.html |access-date=2024-03-20}}

By the standards of the time, a relatively large amount of data could be stored in a small installed volume of core rope memory: 72 kilobytes per cubic foot, or roughly 2.5 megabytes per cubic meter. This was about 18 times the amount of magnetic-core memory (within two cubic feet).{{Citation needed|reason=These measurements don't make sense as the entire computer was one cubic foot.|date=April 2020}}

{{clear}}

{{Reflist}}

• [https://www.youtube.com/watch?time_continue=3&v=ndvmFlg1WmE "Computer for Apollo"] NASA/MIT film from 1965 which demonstrates how rope memory was manufactured.
• [http://authors.library.caltech.edu/5456/01/hrst.mit.edu/hrs/apollo/public/visual3.htm Visual Introduction to the Apollo Guidance Computer, part 3: Manufacturing the Apollo Guidance Computer.] {{Webarchive|url=https://archive.today/20121212011406/http://authors.library.caltech.edu/5456/01/hrst.mit.edu/hrs/apollo/public/visual3.htm |date=2012-12-12 }} – By Raytheon; hosted by the Library of the California Institute of Technology's History of Recent Science & Technology site (originally hosted by the Dibner Institute)
• [http://www.hq.nasa.gov/office/pao/History/computers/Ch2-5.html Computers in Spaceflight: The NASA Experience] – By James Tomayko (Chapter 2, Part 5, "The Apollo guidance computer: Hardware")
• Brent Hilpert's [http://madrona.ca/e/corerope/index.html Core Rope & Woven-Wire Memory Systems] page has a detailed explanation of pulse-transformer and switching-core techniques.
• SV3ORA's [http://qrp.gr/coreROM/ Core rope memory: A practical guide of how to build your own] gives a description, schematics and photos of a simple core rope memory board using the pulse transformer technique, including a demonstration of operation.
• [http://www.righto.com/2019/07/software-woven-into-wire-core-rope-and.html Software woven into wire: Core rope and the Apollo Guidance Computer], extensive blog post by computer restoration expert Ken Shirriff
• [https://connect.adelaide.edu.au/nodes/view/26006#idx219522 Australian 'ropes' demonstrated at MIT] Letter from Ramon L. Alonso to Gordon Rose, dated 10 December 1963: "We are finding the Australian ideas on ‘ropes' to be very fruitful indeed, and we are going ahead with some development work on them."

{{Magnetic storage media}}

{{DEFAULTSORT:Core Rope Memory}}

Category:Computer memory

Category:Non-volatile memory