friction loss

Friction loss is a significant engineering concern wherever fluids are made to flow, whether entirely enclosed in a pipe or duct, or with a surface open to the air.

• Historically, it is a concern in aqueducts of all kinds, throughout human history. It is also relevant to sewer lines. Systematic study traces back to Henry Darcy, an aqueduct engineer.
• Natural flows in river beds are important to human activity; friction loss in a stream bed has an effect on the height of the flow, particularly significant during flooding.
• The economies of pipelines for petrochemical delivery are highly affected by friction loss. The Yamal–Europe pipeline carries methane at a volume flow rate of 32.3 billion m³ of gas per year, at Reynolds numbers greater than 50 million.{{cite journal

| last1=Allen|first1=J.J.

| last2=Shockling|first2=M.

| last3=Kunkel|first3=G.

| last4=Smits|first4=A.J.

| title=Turbulent flow in smooth and rough pipes

| journal=Phil. Trans. R. Soc. A

| date=2007

| volume=365

|issue=1852

| pages=699–714

| doi=10.1098/rsta.2006.1939

|pmid=17244585

|bibcode = 2007RSPTA.365..699A |s2cid=2636599

}} Per EuRoPol GAZ website.

• In hydropower applications, the energy lost to skin friction in flume and penstock is not available for useful work, say generating electricity.
• In refrigeration applications, energy is expended pumping the coolant fluid through pipes or through the condenser. In split systems, the pipes carrying the coolant take the place of the air ducts in HVAC systems.

In the following discussion, we define volumetric flow rate V̇ (i.e. volume of fluid flowing per time) as

$\backslash dot\{V\}\; =\; \backslash pi\; r^2\; v$

where

: r = radius of the pipe (for a pipe of circular section, the internal radius of the pipe).

: v = mean velocity of fluid flowing through the pipe.

: A = cross sectional area of the pipe.

In long pipes, the loss in pressure (assuming the pipe is level) is proportional to the length of pipe involved.

Friction loss is then the change in pressure Δp per unit length of pipe L

:$\backslash frac\{\; \backslash Delta\; p\; \}\{\; L\; \}.$

When the pressure is expressed in terms of the equivalent height of a column of that fluid, as is common with water, the friction loss is expressed as S, the "head loss" per length of pipe, a dimensionless quantity also known as the hydraulic slope.

: $S\; =\; \backslash frac\{h\_f\; \}\{\; L\; \}\; =\; \backslash frac\{\; 1\; \}\{\; \backslash rho\; \backslash mathrm\{g\}\; \}\; \backslash frac\{\; \backslash Delta\; p\; \}\{\; L\; \}\; .$

where

: ρ = density of the fluid, (SI kg / m³)

: g = the local acceleration due to gravity;

Friction loss, which is due to the shear stress between the pipe surface and the fluid flowing within, depends on the conditions of flow and the physical properties of the system. These conditions can be encapsulated into a dimensionless number Re, known as the Reynolds number

:$\backslash mathrm\{Re\}=\backslash frac\{1\}\{\backslash nu\}VD$

where V is the mean fluid velocity and D the diameter of the (cylindrical) pipe. In this expression, the properties of the fluid itself are reduced to the kinematic viscosity ν

:$\backslash nu=\backslash frac\{\backslash mu\}\{\backslash rho\}$

where

: μ = viscosity of the fluid (SI kg / m • s)

The friction loss in uniform, straight sections of pipe, known as "major loss", is caused by the effects of viscosity, the movement of fluid molecules against each other or against the (possibly rough) wall of the pipe. Here, it is greatly affected by whether the flow is laminar (Re < 2000) or turbulent (Re > 4000):

• In laminar flow, losses are proportional to fluid velocity, V; that velocity varies smoothly between the bulk of the fluid and the pipe surface, where it is zero. The roughness of the pipe surface influences neither the fluid flow nor the friction loss.
• In turbulent flow, losses are proportional to the square of the fluid velocity, V²; here, a layer of chaotic eddies and vortices near the pipe surface, called the viscous sub-layer, forms the transition to the bulk flow. In this domain, the effects of the roughness of the pipe surface must be considered. It is useful to characterize that roughness as the ratio of the roughness height ε to the pipe diameter D, the "relative roughness". Three sub-domains pertain to turbulent flow:
• In the smooth pipe domain, friction loss is relatively insensitive to roughness.
• In the rough pipe domain, friction loss is dominated by the relative roughness and is insensitive to Reynolds number.
• In the transition domain, friction loss is sensitive to both.
• For Reynolds numbers 2000 < Re < 4000, the flow is unstable, varying with time as vortices within the flow form and vanish randomly. This domain of flow is not well modeled, nor are the details well understood.

Factors other than straight pipe flow induce friction loss; these are known as "minor loss":

• Fittings, such as bends, couplings, valves, or transitions in hose or pipe diameter, or
• Objects intruded into the fluid flow.

For the purposes of calculating the total friction loss of a system, the sources of form friction are sometimes reduced to an equivalent length of pipe.

The roughness of the surface of the pipe or duct affects the fluid flow in the regime of turbulent flow. Usually denoted by ε, values used for calculations of water flow, for some representative materials are:{{cite web

| title= Pipe Roughness

| url=http://www.pipeflow.com/pipe-pressure-drop-calculations/pipe-roughness

| access-date=5 October 2015

| publisher=Pipe Flow Software

}}{{cite web

| title= Pipe Roughness Data

| url=http://www.efunda.com/formulae/fluids/roughness.cfm

| access-date=5 October 2015

| publisher=Efunda.com

}}{{cite web

| title= Pipe Friction Loss Calculations

| url=http://www.pipeflow.com/pipe-pressure-drop-calculations/pipe-friction-loss

| access-date=5 October 2015

| publisher=Pipe Flow Software

}} The friction factor C in the Hazen-Williams formula takes on various values depending on the pipe material, in an attempt to account for surface roughness.

Values used in calculating friction loss in ducts (for, e.g., air) are:{{cite web

| title= On-Line Duct Friction Loss

| url=http://www.freecalc.com/ductloss.htm

| access-date=8 October 2015

| publisher=FreeCalc.com

}}

Laminar flow is encountered in practice with very viscous fluids, such as motor oil, flowing through small-diameter tubes, at low velocity. Friction loss under conditions of laminar flow follow the Hagen–Poiseuille equation, which is an exact solution to the Navier-Stokes equations. For a circular pipe with a fluid of density ρ and viscosity μ, the hydraulic slope S can be expressed

:$S\; =\; \backslash frac\{64\}\{\backslash mathrm\{Re\}\}\; \backslash frac\{V^2\}\{2gD\}\; =\; \backslash frac\{64\backslash nu\}\{2g\}\; \backslash frac\{V\}\{D^2\}$

In laminar flow (that is, with Re < ~2000), the hydraulic slope is proportional to the flow velocity.

In many practical engineering applications, the fluid flow is more rapid, therefore turbulent rather than laminar. Under turbulent flow, the friction loss is found to be roughly proportional to the square of the flow velocity and inversely proportional to the pipe diameter, that is, the friction loss follows the phenomenological Darcy–Weisbach equation in which the hydraulic slope S can be expressed{{cite conference

|last=Brown

|first=G.O.

|title=The History of the Darcy-Weisbach Equation for Pipe Flow Resistance

|book-title=Environmental and Water Resources History

|publisher=American Society of Civil Engineers

|pages=34–43

|year=2003

|doi=10.1061/40650(2003)4

}}

: $S\; =\; f\_D\; \backslash frac\{\; 1\; \}\{\; 2g\; \}\; \backslash frac\{V^2\}\{D\}$

where we have introduced the Darcy friction factor f_D (but see Confusion with the Fanning friction factor);

: f_D = Darcy friction factor

Note that the value of this dimensionless factor depends on the pipe diameter D and the roughness of the pipe surface ε. Furthermore, it varies as well with the flow velocity V and on the physical properties of the fluid (usually cast together into the Reynolds number Re). Thus, the friction loss is not precisely proportional to the flow velocity squared, nor to the inverse of the pipe diameter: the friction factor takes account of the remaining dependency on these parameters.

From experimental measurements, the general features of the variation of f_D are, for fixed relative roughness ε / D and for Reynolds number Re = V D / ν > ~2000,{{efn|See Moody chart}}

• With relative roughness ε / D < 10⁻⁶, f_D declines in value with increasing Re in an approximate power law, with one order of magnitude change in f_D over four orders of magnitude in Re. This is called the "smooth pipe" regime, where the flow is turbulent but not sensitive to the roughness features of the pipe (because the vortices are much larger than those features).
• At higher roughness, with increasing Reynolds number Re, f_D climbs from its smooth pipe value, approaching an asymptote that itself varies logarithmically with the relative roughness ε / D; this regime is called "rough pipe" flow.
• The point of departure from smooth flow occurs at a Reynolds number roughly inversely proportional to the value of the relative roughness: the higher the relative roughness, the lower the Re of departure. The range of Re and ε / D between smooth pipe flow and rough pipe flow is labeled "transitional". In this region, the measurements of Nikuradse show a decline in the value of f_D with Re, before approaching its asymptotic value from below,{{cite journal

| last1=Nikuradse|first1=J.

| title=Strömungsgesetze in Rauen Rohren

| journal=V. D. I. Forschungsheft

| date=1933

| volume=361

| pages=1–22

}} although Moody chose not to follow those data in his chart,{{citation

| first=L. F. | last=Moody

| title=Friction factors for pipe flow

| journal=Transactions of the ASME

| volume=66

| issue=8

| pages=671–684

| year=1944

| url=https://www.scribd.com/doc/39857323/MoodyLFpaper1944

}} which is based on the Colebrook–White equation.

• At values of 2000 < Re < 4000, there is a critical zone of flow, a transition from laminar to turbulence, where the value of f_D increases from its laminar value of 64 / Re to its smooth pipe value. In this regime, the fluid flow is found to be unstable, with vortices appearing and disappearing within the flow over time.
• The entire dependence of f_D on the pipe diameter D is subsumed into the Reynolds number Re and the relative roughness ε / D, likewise the entire dependence on fluid properties density ρ and viscosity μ is subsumed into the Reynolds number Re. This is called scaling.{{efn|See Reynolds number}}

The experimentally measured values of f_D are fit to reasonable accuracy by the (recursive) Colebrook–White equation,{{cite web

| last1=Rao

| first1=A.

| last2=Kumar

| first2=B.

| title=Friction Factor for Turbulent Pipe Flow

| url=http://eprints.iisc.ernet.in/9587/1/Friction_Factor_for_Turbulent_Pipe_Flow.pdf

| access-date=20 October 2015

}} depicted graphically in the Moody chart which plots friction factor f_D versus Reynolds number Re for selected values of relative roughness ε / D.

File:Flow at Constant Friction Loss in PVC pipe.svg

In a design problem, one may select pipe for a particular hydraulic slope S based on the candidate pipe's diameter D and its roughness ε.

With these quantities as inputs, the friction factor f_D can be expressed in closed form in the Colebrook–White equation or other fitting function, and the flow volume Q and flow velocity V can be calculated therefrom.

In the case of water (ρ = 1 g/cc, μ = 1 g/m/s{{cite web

| title= Water - Dynamic and Kinetic Viscosity

| url=http://www.engineeringtoolbox.com/water-dynamic-kinematic-viscosity-d_596.html

| access-date=5 October 2015

| publisher=Engineering Toolbox

}}) flowing through a 12-inch (300 mm) Schedule-40 PVC pipe (ε = 0.0015 mm, D = 11.938 in.), a hydraulic slope S = 0.01 (1%) is reached at a flow rate Q = 157 lps (liters per second), or at a velocity V = 2.17 m/s (meters per second).

The following table gives Reynolds number Re, Darcy friction factor f_D, flow rate Q, and velocity V such that hydraulic slope S = h_f / L = 0.01, for a variety of nominal pipe (NPS) sizes.

Note that the cited sources recommend that flow velocity be kept below 5 feet / second (~1.5 m/s).

Also note that the given f_D in this table is actually a quantity adopted by the NFPA and the industry, known as C, which has the customary units psi/(100 gpm²ft) and can be calculated using the following relation:

: $\backslash Delta\; P\_f\text{'}\; =\; CQ\text{'}^2L\text{'}$

where $\backslash Delta\; P\_f\text{'}$ is the pressure in psi, $Q\text{'}$ is the flow in 100gpm and $L\text{'}$ is the length of the pipe in 100ft

File:Equal-friction chart for air in metal duct (ε = 0.05mm).svg

Friction loss takes place as a gas, say air, flows through duct work.{{cite web

| title= Duct Design

| last=Elder

| first=Keith E.

| url=http://courses.washington.edu/me425/425-6-Duct%20Design-2007.pdf

| access-date=8 October 2015

}}

The difference in the character of the flow from the case of water in a pipe stems from the differing Reynolds number Re and the roughness of the duct.

The friction loss is customarily given as pressure loss for a given duct length, Δp / L, in units of (US) inches of water for 100 feet or (SI) kg / m² / s².

For specific choices of duct material, and assuming air at standard temperature and pressure (STP), standard charts can be used to calculate the expected friction loss.{{cite web

| title=HVAC Calculations and Duct Sizing

| last=Beckfeld

| first=Gary D.

| url=http://www.pdhonline.org/courses/m199/m199content.pdf

| year=2012

| access-date=8 October 2015

| publisher=PDH Online, 5272 Meadow Estates Drive Fairfax, VA 22030

| archive-date=4 March 2016

| archive-url=https://web.archive.org/web/20160304074216/http://www.pdhonline.org/courses/m199/m199content.pdf

| url-status=dead

}} The chart exhibited in this section can be used to graphically determine the required diameter of duct to be installed in an application where the volume of flow is determined and where the goal is to keep the pressure loss per unit length of duct S below some target value in all portions of the system under study. First, select the desired pressure loss Δp / L, say 1 kg / m² / s² (0.12 in H₂O per 100 ft) on the vertical axis (ordinate). Next scan horizontally to the needed flow volume Q, say 1 m³ / s (2000 cfm): the choice of duct with diameter D = 0.5 m (20 in.) will result in a pressure loss rate Δp / L less than the target value. Note in passing that selecting a duct with diameter D = 0.6 m (24 in.) will result in a loss Δp / L of 0.02 kg / m² / s² (0.02 in H₂O per 100 ft), illustrating the great gains in blower efficiency to be achieved by using modestly larger ducts.

The following table gives flow rate Q such that friction loss per unit length Δp / L (SI kg / m² / s²) is 0.082, 0.245, and 0.816, respectively, for a variety of nominal duct sizes. The three values chosen for friction loss correspond to, in US units inch water column per 100 feet, 0.01, .03, and 0.1. Note that, in approximation, for a given value of flow volume, a step up in duct size (say from 100mm to 120mm) will reduce the friction loss by a factor of 3.

Note that, for the chart and table presented here, flow is in the turbulent, smooth pipe domain, with R* < 5 in all cases.

{{notelist}}

• {{cite journal

| last1=Nikuradse|first1=J.

| title=Gesetzmassigkeiten der Turbulenten Stromung in Glatten Rohren

| journal=VDI Forschungsheft Arb. Ing.-Wes.

| date=1932

| volume=356

| pages=1–36

| url=https://www.princeton.edu/mae/people/faculty/smits/homepage/data-1/nikuradse-data/Nikuradse_German_1932.pdf

}} – In translation, NACA TT F-10 359. The data are available in [https://www.princeton.edu/mae/people/faculty/smits/homepage/data-1/nikuradse-data/Nik-u+-vs-y+-data.xls digital form].

• {{cite journal

|last1=Kemler|first1=E.

|title=A Study of the Data on the Flow of Fluid in Pipes

|journal=Transactions of the ASME

|date=1933

|volume=55

|issue=Hyd-55-2

|pages=7–32

}} Cited by Moody, L. F. (1944)

• {{cite journal

|last1=Nikuradse|first1=J.

|title=Strömungsgesetze in rauen Rohren

|journal=V. D. I. Forschungsheft

|date=1933

|volume=361

|pages=1–22

|url=https://www.princeton.edu/mae/people/faculty/smits/homepage/data-1/nikuradse-data/Nikuradse_rough_English.pdf

}} – In English translation, as [https://ntrs.nasa.gov/archive/nasa/casi.ntrs.nasa.gov/19930093938.pdf NACA TM 1292, 1950]. [https://www.princeton.edu/mae/people/faculty/smits/homepage/data-1/nikuradse-data/NikRough_f_vs_Re.xls The data] show in detail the transition region for pipes with high relative roughness (ε/D > 0.001).

• {{cite journal

| title = Experiments with Fluid Friction in Roughened Pipes

| last1=Colebrook | first1=C. F.

| last2=White | first2=C. M.

| journal = Proceedings of the Royal Society of London. Series A, Mathematical and Physical Sciences

| volume = 161

| pages = 367–381

| year = 1937

| issue = 906

| doi = 10.1098/rspa.1937.0150

| bibcode = 1937RSPSA.161..367C

| url=https://www.scribd.com/doc/212809091/367-full

| doi-access = free

}}

• {{cite journal

| last=Colebrook | first=C. F.

| title=Turbulent flow in pipes, with particular reference to the transition region between smooth and rough pipe laws

| journal=Journal of the Institution of Civil Engineers

| date=February 1939

| url=https://www.scribd.com/doc/269398414/Colebrook-White-1939

}}

• {{cite book

|last1=Rouse|first1=H.

|title=Evaluation of Boundary Roughness

|date=1943

|publisher=Proceedings Second Hydraulic Conference, University of Iowa Bulletin 27

}} Cited by Moody, L. F. (1944)

• {{cite book

| last1=Rouse|first1=H.

| title=Elementary Mechanics of Fluids

| url=https://archive.org/details/in.ernet.dli.2015.140493| date=1946

| publisher=John Wiley and Sons

| pages=[https://archive.org/details/in.ernet.dli.2015.140493/page/n369 376]

}} Exhibits Nikuradse data.

• {{cite web

| last1=U.S. Bureau of Reclamation

| title=Friction factors for large conduit flowing full

| date=1965

| series=Engineering Monograph No. 7

| publisher=U.S. Dept. of Interior

| location=Washington, D.C.

|url=https://www.scribd.com/doc/79596055/Friction-Factors-for-Large-Conduits-Flowing-Full

}} Large amounts of field data on commercial pipes. The Colebrook–White equation was found inadequate over a wide range of flow conditions.

• {{cite journal

| last1=Swanson|first1=C. J.

| last2=Julian|first2=B.

| last3=Ihas|first3=G. G.

| last4=Donnelly|first4=R. J.

| title=Pipe flow measurements over a wide range of Reynolds numbers using liquid helium and various gases

| journal=J. Fluid Mech.

| date=2002

| volume=461

|issue=1

| pages=51–60

| doi=10.1017/S0022112002008595

|bibcode = 2002JFM...461...51S |s2cid=120934829

}}

• {{cite journal

| last1=McKeon|first1=B. J.|author1-link= Beverley McKeon

| last2=Swanson|first2=C. J.

| last3=Zagarola|first3=M. V

| last4=Donnelly|first4=R. J.

| last5=Smits|first5=A. J.

| title=Friction factors for smooth pipe flow

| journal=J. Fluid Mech.

| date=2004

| volume=511

| pages=41–44

| doi=10.1017/S0022112004009796

|doi-broken-date=2 December 2024 | url=http://www.mckeon.caltech.edu/publications/pdfs/jfm511oregon.pdf

| access-date=20 October 2015

|bibcode = 2004JFM...511...41M |s2cid=122063338}} Shows friction factor in the smooth flow region for 1 < Re < 10⁸ from two very different measurements.

• {{cite journal

| last1=Shockling|first1=M.A.

| last2=Allen|first2=J.J.

| last3=Smits|first3=A.J.

| title=Roughness effects in turbulent pipe flow

| journal=J. Fluid Mech.

| date=2006

| volume=564

| pages=267–285

|bibcode = 2006JFM...564..267S |doi = 10.1017/S0022112006001467 |doi-broken-date=29 November 2024

|s2cid=120958504

}}

• {{cite journal

| last1=Allen|first1=J.J.

| last2=Shockling|first2=M.

| last3=Kunkel|first3=G.

| last4=Smits|first4=A.J.

| title=Turbulent flow in smooth and rough pipes

| journal=Phil. Trans. R. Soc. A

| date=2007

| volume=365

|issue=1852

| pages=699–714

| doi=10.1098/rsta.2006.1939

|pmid=17244585

|bibcode = 2007RSPTA.365..699A |s2cid=2636599

}}

{{reflist}}

• [http://www.enggcyclopedia.com/welcome-to-enggcyclopedia/fluid-dynamics/line-sizing-calculator Pipe pressure drop calculator] {{Webarchive|url=https://web.archive.org/web/20190713054058/http://www.enggcyclopedia.com/welcome-to-enggcyclopedia/fluid-dynamics/line-sizing-calculator |date=2019-07-13 }} for single phase flows.
• [http://www.enggcyclopedia.com/welcome-to-enggcyclopedia/fluid-dynamics/pipe-pressure-drop-calculator-phase Pipe pressure drop calculator for two phase flows.] {{Webarchive|url=https://web.archive.org/web/20190713054058/http://www.enggcyclopedia.com/welcome-to-enggcyclopedia/fluid-dynamics/pipe-pressure-drop-calculator-phase |date=2019-07-13 }}
• [http://pfcalc.sourceforge.net Open source pipe pressure drop calculator.]

Category:Friction

Category:Fluid dynamics

Category:Fluid mechanics

Category:Mechanical engineering

Category:Piping