Schneider ES-65
{{Infobox aircraft
| name=ES-65 Platypus
| image=Platypus-jun06.jpg
| caption=
| type=Two seat advanced trainer
| national_origin=Australia
| manufacturer=Edmund Schneider Pty, Adelaide
| designer=Harry Schneider
| first_flight=August 1984
| introduction=
| retired=
| status=
| primary_user=
| more_users=
| produced=
| number_built=1
| program cost=
| unit cost=
| developed_from=
| variants=
}}
The Schneider ES-65 Platypus is a two-seater unflapped glider designed and built by Edmund Schneider Pty in Australia. A single prototype was built, which remains operational as of 2012.
Design and development
The Edmund Schneider company was originally based in Grunau, Silesia but reformed after World War II in Adelaide, Australia, producing the successful Schneider ES-60 from 1960 until 1970. Anticipating an Australian market for an ES-60-based side by side two-seater Harry Schneider began design and construction of the ES-64, a marriage of ES-60 wings with a new glass reinforced plastic (GRP) fuselage. Australian gliding clubs showed little interest and the project proceeded slowly. In the early 1980s Schneider revived it with a simplified version, the ES-65 Platypus.
The Platypus has the extended plywood skinned ES-60 wing, built around a single spar. The leading edge is unswept but the straight trailing edges have forward sweep that increases on the outer, aileron-carrying, panels. There are airbrakes mounted just aft of the spar on the inner panels. These wings were mid-mounted onto a new GRP fuselage. This has a maximum width of 1.20 m (3 ft 11 in) to accommodate the side by side seating but narrowed in pod and boom style, particularly in plan, behind the wings. The cockpit has a two-piece fixed screen extending almost to the nose and is accessed via a rear hinged, bulged canopy. The pod includes a fixed, faired, centre-line two wheel undercarriage, with a brake-equipped mainwheel under the wings and a smaller nosewheel.
The tail is also mostly GRP, though the elevator uses carbon fibre for lightness. These surfaces are straight-edged and tapering, the fin is tall with a rudder that extends to the bottom of the fuselage. The high aspect ratio horizontal tail surface is mounted midway up the fin.
The Platypus made its first flight in August 1984 and its handling and performance were generally judged to be good. There were plans to produce an all-GRP version, but the funding required was not available and no more ES-65s were built.
Operational history
Specifications
{{Aircraft specs
|prime units?=met
|genhide=
|crew=2
|length m=7.726
|length note=
|span m=17.70
|span note=
|height m=1.7
|wing area sqm=16.2
|wing area note=
|aspect ratio=19.3
|airfoil=Wortmann FX61-164 root, FX61-140 inboard of aileron, FX60-126 tip
|empty weight kg=400
|empty weight note=
|gross weight kg=590
|gross weight lb=
|gross weight note=
|max takeoff weight kg=
|max takeoff weight lb=
|max takeoff weight note=
|more general=
|perfhide=
|max speed kts=140
|cruise speed kmh=
|cruise speed mph=
|cruise speed kts=
|cruise speed note=
|stall speed kmh=72
|never exceed speed kts=140
|minimum control speed kmh=
|minimum control speed mph=
|minimum control speed kts=
|minimum control speed note=
|ceiling m=
|ceiling ft=
|ceiling note=
|g limits=
|roll rate=
|sink rate ms=
|sink rate ftmin=
|sink rate note=
|lift to drag=
|wing loading kg/m2=36.4
|wing loading note=
|more performance=
|avionics=
}}
{{aircontent
|see also=
|related=
|similar aircraft=
|lists=
}}
References
{{Commons category}}
{{reflist|refs=
}}
{{Edmund Schneider aircraft}}
Category:1980s Australian sailplanes
Category:Aircraft first flown in 1984
Category:Cruciform tail aircraft