Springboard
{{Short description|Board that is itself a spring, used for diving}}
{{About|the springboard used in diving}}
{{Use mdy dates|date=July 2012}}
A springboard or diving board is used for diving and is a board that is itself a spring, i.e. a linear flex-spring, of the cantilever type.
Springboards are commonly fixed by a hinge at one end (so they can be flipped up when not in use), and the other end usually hangs over a swimming pool, with a point midway between the hinge and the end resting on an adjustable fulcrum.
Springboard materials
Modern springboards are made out of a single-piece extrusion of aircraft-grade aluminum. The Maxiflex Model B, the board used in all major competitive diving events,{{cite web|url=http://diving.about.com/od/facilities/a/cheeseboard.htm|title=Why a Diving Board Has Holes|first=Woody|last=Franklin|publisher=About.com|access-date=June 8, 2012|archive-url=https://web.archive.org/web/20121118185534/http://diving.about.com/od/facilities/a/cheeseboard.htm|archive-date=November 18, 2012}} is made out of such aluminum, and is heat treated for a yield strength of {{Convert |340000 |kPa| abbr=on |sp=us}}. The slip-resistant surface of the board is created using an epoxy resin, finished with a laminate of flint silica and alumina in between the top coats of resin. This thermal-cured resin is aqua-colored to match the water of a clean pool.[http://www.duraflexinternational.com/product_info.php?cPath=27_22&products_id=31 duraflexinternational.com] {{webarchive|url=https://web.archive.org/web/20090727214818/http://www.duraflexinternational.com/product_info.php?cPath=27_22&products_id=31 |date=July 27, 2009 }}
Adjustment of the spring constant
The spring constant of a springboard is usually adjusted by way of a fulcrum that is located approximately mid way along the springboard. Springboards are usually operated in a linear regime where they approximately obey Hooke's law. When loaded with a diver, the combination of the diver's approximately constant mass, and the constant stiffness of the spring(board) result in a resonance frequency that is adjustable by way of the spring constant (set by the fulcrum position). Since the resulting system is in an approximately linear regime, it may be modeled fairly accurately by a second order differential equation. Typically the resonance frequency can be adjusted over a range of a 2:1 or 3:1 ratio.[https://web.archive.org/web/20030525160250/http://www.unc.edu/~lahol/ The Physics of Springboard and Platform Diving]
Adjusting the fulcrum
The fulcrum on competitive diving boards travels over a range of {{convert|0.61|m|in|abbr=off}},{{Cite web|url=http://diving.about.com/od/facilities/tp/anatBoard.htm|title=Sports}} and is set by way of a foot wheel that is approximately {{convert|0.35|m|in|abbr=on}} in diameter.{{Cite web |url=http://diving.about.com/od/divingglossary/g/fulcrumDef.htm |title=Diving Fulcrum |access-date=October 6, 2010 |archive-date=July 7, 2011 |archive-url=https://web.archive.org/web/20110707074933/http://diving.about.com/od/divingglossary/g/fulcrumDef.htm |url-status=dead }}[http://diving.about.com/od/facilities/tp/anatBoard.htm Duraflex International/Coach woody Franklyn: diving board construction]. To stiffen the spring (as if tightening it), the foot wheel is usually turned counter clockwise. Some may find this counter intuitive, since usually things are tightened by turning clockwise. However, with a little experience, people realize the fulcrum moves in the direction the bottom of the foot faces when placed on the foot wheel.
:Note – Standing behind or in front of the knob, rather than directly above it, will provide better leverage to move the fulcrum. This is accomplished by holding on to the hand rails and leaning the body a few degrees, then placing the foot as low as possible on the knob. In this way, it is possible to move even the most difficult fulcrum.
Heights of springboards
Springboards are usually located either {{convert|1.0|or|3.0|m|ftin}} above the water surface. It is very seldom that one is mounted at a height other than these two standard heights.
Before around 1960, springboards, usually made of wood, were located at heights of either {{convert|3|m|ft|sigfig=1|disp=x| (approximately |)}}, or {{convert|6|m|ft|sigfig=1|disp=x| (approximately |)}} above the water. American artist Norman Rockwell's painting titled Boy on High Dive (1947) shows a boy (Rockwel's youngest son, Peter) peering over a typical wooden springboard of the early 20th century era at the 20 feet height.{{Cite web|title=Boy On HighDive, Norman Rockwell Saturday Evening Post Cover 1947|url=http://www.best-norman-rockwell-art.com/1947-boy-on-highdive.html|access-date=2021-08-06|website=Best-Norman-Rockwell-Art.com}}
Home springboards
After an incident in Washington in 1993, most US and other pool builders are reluctant to equip a residential swimming pool with a diving springboard so home diving pools are much less common these days. In the incident, 14-year-old Shawn Meneely made a "suicide dive" (holding his hands at his sides, so that his head hit the bottom first) in a private swimming pool and was seriously injured and became a tetraplegic. The lawyers for the family, Jan Eric Peterson and Fred Zeder, successfully sued the diving board manufacturer, the pool builder, and the National Spa and Pool Institute (NSPI) over the inappropriate depth of the pool.{{cite news |first=AmyJo|last=Brown|title=No Diving?|url=http://www.poolspanews.com/2004/012/012diving.html|publisher=Pool & Spa News| date=January 30, 2004|access-date=2007-04-15|archive-url=https://web.archive.org/web/20040304034008/http://www.poolspanews.com/2004/012/012diving.html|archive-date=March 4, 2004 }}{{cite web | title=Deep Impact: Back Yard Danger | url=https://www.cbsnews.com/news/deep-impact-back-yard-danger/|publisher=CBS News|work=60 Minutes II|date=June 2, 1999|access-date=January 5, 2012}}
The NSPI had specified a minimum depth of {{convert|7|ft|6|in|m|abbr=on}} which proved to be insufficient in the above case. The pool into which Meneely dived was not constructed to the published standards. The standards had changed after the diving board was installed on the non-compliant pool by the homeowner. But the courts held that the pool "was close enough" to the standards to hold NSPI liable. The multimillion-dollar lawsuit was eventually resolved in 2001 for US$6.6 million ($8 million after interest was added) in favor of the plaintiff.Appeals Court State of WA, Docket Number:18036-1-III
Title: Shawn Meneely, et al. v. S. R. Smith, Inc., et al. The NSPI was held to be liable, and was financially strained by the case. It filed twice for Chapter 11 bankruptcy protection and was successfully reorganized into a new swimming pool industry association.